2001 FMC Frigoscandia Advantec Impingement Freezer/Chiller. Model 2M-1800-1, S/N 01080018. Rating on hamburger patties: 3,500 lbs/hr based on 1/4 inch thick patties, 1/4 lb each,10 across on belt, belt length 35 ft... 100 seconds dwell time, using 46 tons at -40 °F. Single belt: 49 in. W (1250 mm). This impingement freezer/chiller, is ideal for quick freezing thin products with minimal dehydration, gentle product handling and high product quality. A major food manufacturer paid over $750,000 for this unit in 2001. This major food manufacturer had this at a co-packer that sold to their largest competitor so they removed it. It is as close to new as you can get. Overall dimensions: 53 ft. 8 in. L x 14 ft. W x 12 ft. H.
1993 IJ White Stainless Steel Spiral Freezer. Approx 16-Tier high. 14 ft. Dia. Product clearance 24 in. W x 4-1/2 in. H. 720 ft. x 26 in. W stainless steel metal link belt conveyor. Set up to do 3,000 lbs/hr of various cuts of beef. Refrigerating system coils rated 45 tons. Belt tensioning system, bally modular insulated freezer room. Frick refrigerating system, heat exchange coils in box. Frick Model RNB11-134E Liquid Chiller (S/N: S0564MFMPTUAB3), Caterpillar Model 3306SI, 6-Cylinder, 185 hp Diesel engine, natural gas (S/N: 07404356). Frick Model PRR Refrigerant roof mount recirculation, roof mounted condenser, inclined metal link discharge conveyor. Set up to do 3,000 lbs/hr of various cuts of beef. Refrigerating system coils rated 45 Tons. We will change the gas motor to electric motor at no charge if customer desires. Overall dimensions: 26 ft. 11 in. L x 22 ft. 2-1/2 in. W x 15 ft. H.
Freezing Systems Spiro-Freeze Spiral Freezer. This freezer will allow user to freeze two separate product streams at the same time. Air inflow is from top down through center and then up through stacked tiers containing product before. (2)Infeed belts begin side by side and stack as they enter the freezer. Last used to freeze 1.8 oz eggplant pieces. Pieces entered at 180 °F with a 22 minute dwell time and exited at 18-20 °F. Capacity: approx. 2600 lbs/hr. Spiral freezer: 1 tower, 2 stacks, 8.5 tiers each. Infeed height: 36 in. each belt. Discharge height: belt #1- 11.3 in.; belt #2- 11.9 in. Tier spacing: 6 in. Product clearance: 3 in. Belt width: 30 in.; usable 28 in. Active belt length: 854 ft.; total belt length 1110 ft. Ram AC variable drive: 7.5 hp. 1999 Frick rotary screw compressor, motor 400 hp. 3,600 rpm. (6) Fans, air vol. 140,800 cfm, 7.5 hp. 1999 Imeco condenser, evaporator, 1999 Frick separator, receiver, electric control panels. Overall dimensions: 35 ft L x 35 ft W x 15 ft H. Installed in 2000; decommissioned in October 2005. Ran 50 weeks/yr; 45 hrs/week.
Morris & Associates IQF Freezer. Stainless steel. Model: CBF-20T-248-32, S/N: 942-573. Continuous 24 in. stainless steel belt; 8 passes, 3,000 lbs peas/hr. Overall dimensions: 34 ft. L x 7-1/2 ft. W x 9 ft. H.
Ross BLC-200 IMPINGEMENT IQF Freezer--Two modules-- 3 PASS, Cascade Configuration-28in wide conveyors--Fabrication 1990--- with stainless steel conveyors and frame; panels are stainless outside/fiberglass inside--polyurethane foamed-in-place insulation. Capacity 600 up to 1200 Pounds hamburger patties each hour (in at +45ºF out at +0ºF core temperature in five to seven minutes) --includes Control Panel with variable speed drives for both fan motors and two VSD's for conveyors [one for top conveyor; second VSD for bottom two conveyors]. Each module contains a 15 ton evaporator coil w/ 15 hp fan motor. Total of 30 T.R. Additional information on this iqf tunnel in PDF file.
Chemetron 3 Pass Liquid CO2 Cryogenic Freezer
Mfg: Chemetron
Model:Ultra Freeze
Stock No. DSBI072.11a
Serial:
Chemetron 3 Pass Liquid CO2 Cryogenic Freezer. Model: Ultra Freeze. (3) Stainless steel mesh belts. Mesh size opening: 1/2 in. x 1 in. Height available above belts: approx. 2-1/2 in. Belt: 48 ft. L x 32 in. W. (8) panel sections per side of tunnel with (2) fans per section. (16) Baldor fan motors: 1 hp, 1140 rpm, 230/460 V, 3.4/1.7 amps, 60 Hz, 3 phase. (2) Conveyor motors: 3/4 hp, 1725 rpm, 230/460 V, 2.2/1.1 amps, 60 Hz, 3 phase. Boston Reducer. Penta-Drive DC motor speed control. Overall dimensions: 48 ft. L x 4 ft. 10 in. W x 5ft. 6 in. H.
Integrated Process Systems Cryotransfer IQF Tunnel
Mfg: Integrated Process Systems
Model:CK
Stock No. JHFL001.50
Serial: 71142-CK2004
Integrated Process Systems Cryotransfer IQF Tunnel. Model: CK. SN: 71142-CK2004. Liquid Nitrogen Flash Freeze Process. Product clearance: 48 in. W x 7-1/2 in. H. Belt width: 24 in. Uses (8) 16 in. dia. cooling fans with Reliance Motors, 1/2 hp, 1725 rpm, 230/460 V, 2.2/1.1 amps, 60 Hz, 3 phase. (2) Reliance Electric Conveyor Motors, 1-1/2 hp, 1725 rpm, 230/460 V, 6.4/3.2 amps, 60 Hz, 3 phase. Reese RV Drive, gear ratio: 70, final speed: 60 rpm. (2) 12 in. dia. blowers one with motor. Piston-assist, lift-top covers. Conveyor infeed height: 45 in. Conveyor exit height: 40 in. Overall dimensions: 53 ft. 5 in. L x 89 in. W x 77 in. H.
SMB Stainless Steel Cooling Tunnel. Model: 04.1.0.213. S/N: 3325. Maximum aperture/clearance above belt per section: 6 ft. 5 in. W x 9 in. H. Conveyor infeed maximum aperture/clearance: 1 ft. 3 in. W x 12 in. H. Conveyor infeed/exit height: 40 in. (14) 11-1/2 in. W x 6 in. H pan access ports. Sew-Eurodrive Motor (infeed conveyor), 4 hp (3 kW), 1700 rpm, 330/575 V, 7.9/4.55 amps, 60 Hz, 3 phase. Sew-Eurodrive Variable Speed Drive. Sew-Eurodrive Motor (infeed conveyor), 4 hp (3 kW), 1700 rpm, 330/575 V, 7.9/4.55 amps, 60 Hz, 3 phase. Sew-Eurodrive Variable Speed Drive, 9.1 rpm (min), 45.6 rpm (max). SMB Stainless Steel Control Panel, includes toggle switches for: pump controls, conveyor controls, run controls. SMB Centrifugal Pumps. ASEA Motors, 2.0 hp, 1730 rpm, 575 V, 2.5 amps, 60 Hz, 3 phase. (2) Fischbach Compact Fan Blowers. Brook Compton and Teco Electric Motors, 5 hp, 1740 and 1750 rpm, 575 V, 5.4 and 5.04 amps, 60 Hz, 3 phase. Inlets: (1) 1-1/2 in. dia. media port, (1) 2 in. dia. NPT (media), (1) 2 in. dia. flanged port (media), (1) 2-1/2 in. dia. FNPT (media), (1) 3 in. dia. port (cooling media). Outlets: (1) 1 in. dia. NPT (condensate), (1) 3 in. dia. discharge port (media). Overall dimensions: 67 ft. 3 in. L x 19 ft. 2 in. W x 7 ft. 1 in. H. (ACN5400).
1992 Freezing Systems Inc. Spiral Freezer. Model: 1618-(2)47-L18D. Spiral conveyor diameter: 8 ft. 7 in. Stainless Steel Honeycomb Flat Wire Conveyor, belt width: 16 in. with approximately 18 tiers. Gap between links (min/max): 1/2 in. & 1 in., thickness of flat wire: 0.06 in., distance between guides: 2-3/4 in., distance between rods: 1.122 in., rod diameter: 0.20 in. Container dimensions: 2-5/8 in. L x 2-5/8 in. W x 2-1/4 in. H. U.S. Electric Motor, 10 hp, 1755 rpm, 230/460 V, 27.2/33.4 amps, 60 Hz, 3 phase. 1992 Rex Planet Gear Speed Reducer, Model: VCIA0444-15497, S/N: 15497-1A, ratio: 69.63, rpm in: 1750, rpm out: 25, torque: 20,000 in-lb. Hub City Drive, Model: 66, style: 928, ratio: 1. Centric Clutch, S/N: 204337. Internal Century System Control Panel, S/N: J02-92102-11. Power supply: 460 V, 30 amps, 60 Hz, 3 phase. Conveyor infeed height: 2 ft. 2 in. Conveyor exit height: 11 ft. 2 in. Overall dimensions: 11 ft. 1/2 in. L x 9 ft. 6 in. W x 12 ft. H. 1992 McCormack Evaporative Condenser. Model: 47 Spiral Evaporator. S/N's: 9262E-1, 9262E-2. Combined coil capacity: 62.0 TR at 10 degree TD. Refrigeration type: R-717 (ammonia). (576) 15/16 in. dia. x 10 ft. 10 in. L tubes. Approx. coil volume: 220 gal. (2) fins per in. Power supply: 460 volts, 60 Hz, 3 phase. Design pressure: 150 psi. Test pressure: 400 psig. (4) 42 in. dia. fans, 7.5 hp, 2 amps. Inlets: (2) 5 in. dia. ammonia infeed flanged ports, (1) 2-1/2 in. dia. liquid infeed port. Outlets: (2) 4 in. dia. ammonia discharge flanged ports, (1) 6 in. dia. discharge port. Overall dimensions: 13 ft. 8 in. L x 10 ft. W x 11 ft. 8 in. H. 1992 Morfab Company Ammonia Surge Drum- 700 Gallon. S/N: 4737. Nat'l Bd: 3737. Inside straight-wall dimensions: 3 ft. 6 in. dia. x 9 ft. 11 in. L. Hansen Technologies Float, S/N: PK32B, Cat. No: ER.04N, Size: 3 ft. 4 in. probe. Inlets: (1) 1-1/2 in. dia. liquid feed port, (1) 6 in. dia. compressor suction port, (1) 8 in. dia. liquid suction flanged port, (1) 8 in. dia. liquid suction port. Outlet: (1) 5 in. dia. liquid-out port, (1) 1/2 in. dia. FNPT fitting. This was last used for cooling small pudding containers. Overall dimensions: 10 ft. 11 in. L x 7 ft. 1-1/2 in. W x 5 ft. 8 in. H.
Refrigeration Engineering Corporation (RECO) Cascade IQF Freezer. Model 60. Average capacity: 5000 lbs./hr. Material of construction: 304 stainless steel parts include: mesh belt and side chains, inner “skin” and outer surface cladded panels over plywood. (4) freezer fans, 15 hp required for each. (2) belt drives. (5) hydraulic power motors. Reco’s patented Cascade type of IQF freezer fluidizes, agitates and uniformly glazes product in coordination with high velocity, low temperature air directed from beneath its conveyor belt. Product loading and belt devices may include: a dewatering shaker and shaker spreader for wet vegetables, a product feeder metering device, belt washer dryer and heater, and a refrigeration evaporator(aluminum plate finned coil heat exchanger). Finally, the electrical control panel is complete, waterproof and includes all necessary components for operation. Mounting options include two areas on the machine or in a remote location. Typical applications include: vegetables and fruits with maximum cut sizes of 1-1/2 in. Overall dimensions: 33 ft. L x 11 ft. 6 in. W x 12 ft. H.
APV Crepaco Amerio Horizontal Plate Freezer. S/N: C-0947. (17) 5 ft. 1 in. L x 3 ft. 8 in. W plates. Plate material: sea water resistant aluminum. Distance between plates: 2-7/16 in. (25) 1 ft. 8-3/4 in. L x 11-3/4 in. W x 2-1/4 in. H. product trays. Stainless Steel Control Panel, 2 ft. W x 2 ft. H. Plate freezer used for the rapid freezing of seafood, meats and meat products, poultry, vegetables, and other food products. Inlets: (2) 3/4 in. nitrogen infeed FNPT fittings, (1) 5 ft. 9 in. W x 6 ft. 9 in. H product infeed. Outlets: (1) 1-1/4 in. dia. FNPT fitting, (1) 5 ft. 9 in. W x 6 ft. 9 in. H product discharge. Overall dimensions: 8 ft. 8 in. L x 6 ft. 3 in. W x 8 ft. 11 in. H.
1986 Ammonia Blast Freezer Coils. Model FFN137-0312-AA-4159-717R and L. Aluminum coil rated for 80 tons @ 10.5 deg. FTD. Hot gas defrost. Unit is 20 ft. long x 7 ft. wide x 16 ft. high. (4) - 15 hp fans with air turning vanes on top.
AFPE IQF tunnel freezer, 1998, Model 6.8-5-100-DW, last used to freeze 7,800 lbs/hr lima beans. Freezer belt is stainless steel fine woven wire mesh, drops product about 6 in. to second belt about halfway through tunnel. Belt is 58 in. wide (useable) x 25 ft. total length. High velocity air blows up through belt, circulates through product and then passes through frost belt before going through aluminum coils. Two coils, 8 ft. long & 15 ft. long, base load of 40 tons, total duty load 155 tons, -30 degrees F. Refrigerant R-22 supplied by plant. Easily converted to ammonia. Overall dimensions 25 ft. L x 16 ft. W x 15 ft. H.
SOLD
Frick IQF Freezer Model FP-35 Last used running 8,000 lbs / hr of peas. It has a single pass 48 in. wide stainless steel mesh belt and 35 ft. freezing chamber with (7) 15 hp fans. Overall dimensions are 50 ft. 8 in. L x 12 ft. 6 in. H x 10 ft. 10 in. W. Galvanized frame and interior, stainless steel exterior, and stainless steel product contact surfaces. Ammonia coils are spiral wound galvanized with water defrost sprays. I can paint the inside galvanized interior with food grade epoxy paint prior to loading.
SOLD
Elliot Pasteurizer/Cooler. Model: 8X40. S/N: 20670. Stainless steel. Belt width: 96 in. Maximum aperture/clearance above belt: 93 in. W x 10 in. H. Overhead sprayers, fed by multiple distribution manifolds, pasteurize/cool product. System is equipped with (3) 12 in. L x 12 in. W x 24 in. H side-mounted waste tanks. Infeed/exit height: 38 in. Inlets: (1) 3 in. dia. S-line fitting (cold/hot process), (1) 3 in. dia. bevel fitting (CIP), (2) 13 in. L x 10 in. W infeed ducts. Outlets: (1) 3 in. dia. threaded fitting (waste), (1) 20 in. dia. vent, (2) 29 in. dia. vents. Overall dimensions: 53 ft. 4 in. L x 10 ft. W x 84 in. H. SOLD
1986 Ammonia Blast Freezer Coils. Model FFN137-0312-AA-4159-717R and L. Aluminum coil rated for 80 tons @ 10.5 deg. FTD. Hot gas defrost. Unit is 20 ft. long x 7 ft. wide x 16 ft. high. (4) - 15 hp fans with air turning vanes on top.
SOLD
SOLD DMP/Stainless Fabrication Inc. Roaster-Chiller Tank SOLD
Mfg: DMP/Stainless Fabrication Inc.
Model:
Stock No. DPFI763.19a
Serial: 3109-8
DMP/Stainless Fabrication Inc. Roaster-Chiller Tank. Minimum capacity: 2,261.9 cu. ft. Maximum capacity: 3,378.9 cu. ft. Double wall stainless steel sectional tank with a 2.5 in. W hollow. System uses (4) 20 ft. L x 9 in. W bottom scrape agitators. Windmill-style unloader with (4) 28 in. L x 18 in. W scrapers. Unit features dual 80 ft. L x 12 in. W x 9 in. H channels. (4) Baldor Industrial Motors, 2 hp, 1740 rpm, 230/460 V, 5.6/2.8 amps, 60 Hz, 3 phase. (4) Boston Motor Drives, no nameplate information. Inlets: (24) 1 in. diameter NPT (male-jacket), (1) 30 in. W x 12 in. H. Infeed hopper. Outlets: (16) 1 in. dia. jacket ports, (1) 4 in. diameter NPT (female-tank). Overall dimensions are 90 ft. L x 97 in. W x 90 in. H.
Martin/Baron CO2 Stainless Steel Tunnel. Model MBI 1-38-0028-01. S/N: J990202. 304 stainless steel tunnel is composed of two sections and features a 1 in. chain link belt made of 304 stainless steel. Maximum product clearance/aperture above belt: 40 in. W x 5-1/2 in. H. Tunnel has (9) 19-1/2 in. dia. fans. Electrical requirements: 460 V, 40 amps, 60 Hz, 3-phase. (10) 1 hp Baldor motors, 1,725 rpm, 208-230/460, 3.5-3.2/1.6 amps, 60 Hz. Overall dimensions: 372 in. L x 56 in. W x 50-1/2 in. H.
APV AMERIO automatic contact plate freezer MODEL 35 oversized. (previously used by MeadowGold Dairy) with 14 stations/15 aluminum plates --96-1/4" gross wide (92" net freezing surface) x 144" long with stainless steel reinforced ammonia hoses (1" suction & .5" liquid) + four extra sets of hoses & hose manifolds & all fittings for connections in/out of plates and connections to suction and discharge manifolds, complete frame, catch arms, hydraulic cylinders with yokes, loader/unloader push arm assembly, hydraulic power unit assembly, stainless steel push button relay control panel, and liquid & suction vertical headers. Unit complete with stainless steel enclosure, microswitches and controls on the frame; front and discharge conveyors; and stainless steel steps/platforms front & back. The base has been cut in half to make this a legal wide load -cut so it can be welded back together when installed. And two HANSEN 5 hp hermetic ammonia pumps w/ control valves. Maximum width is 8 ft. 8 in. wide (one piece) and maximum height is 9 ft. 6 in.
SOLD APV Gaulin Amerio Ice Cream Hardening Tunnel SOLD
Mfg: APV Gaulin
Model:
Stock No. 1400.RWMG109
Serial:
APV Gaulin Amerio ice cream hardening tunnel with Reco ammonia recirculator 4-1/2 ft. dia. x 12 ft. L. Control panel with A-B SLC 5/02 cpu, hydraulic power unit. Overall dimension 11 ft. x 12 ft. 8 in. x 14 ft. 5 in. high (rebuilt in 1996 by APV)
Union Carbide CO2 Tunnel. Model: CFF-4835. S/N: 218. Stainless steel. (15) Reliance Electric Motors, ½ hp, 1725 rpm, 230/460 V, 2.2/1.1 amps, 60 Hz, 3 phase. CO2 injection system. Pipe dia.: 1 in. with 5-1/2 in. of insulation. Stainless steel belt dimensions: 25 ft. 41 in. L x 48 in. W. Clearance inlet: 48 in. W x 4 in. H. Distance from fan to belt: 7-1/2 in. H. (4) doors. Control panel with (2) temperature gauges from -100°F to 100°F. Switches: circulation fan, zone, Hand/Auto, exhaust fans, zone 2, Hand/Auto. Switch for stop emergency. Overall dimensions: 33 ft. 16 in. L x 65 in. W x 90 in. H.
