Used 1992 Ketema Inc. Heat Transfer Division DXMB Shell and Tube Heat Exchanger - 50.4 square ft

Used 1992 Ketema Inc. Heat Transfer Division DXMB Shell and Tube Heat Exchanger. Model: 607-Q-SP-1C. Serial Number: U9224129. P/N: 410-00200-002. Nat'l Bd: 5402. Tube material: carbon steel. Number of passes: 4. Number of tubes: 55. Tube dimensions: 1/2 inches diameter x 7 feet L. Heat transfer surface area: 50.4 feet square Tube volume: 4 gal. MAWP shell side: 300 psi @ 200 °F. MDMT shell side: -20°F @ 300 psi. MAWP tube side: 300 psi @ 300°F. MDMT tube side: -20°F @ 300 psi. Inlets: [1] 1/2 inches diameter product feed, [1] 1-1/2 inches diameter media feed. Outlets: [1] 3/4 inches diameter media discharge, [1] 3/4 inches diameter media drain, [1] 1 inches diameter bevel with hex safety relief, [1] 1-1/4 inches diameter product discharge. Overall dimensions 4 feet length x 1 feet 2 inches width x 10 feet 7 inches height.

Used 1990 Cherry-Burrell Shell and Tube Heat Exchanger – 27.35 square feet

Used 1990 Cherry-Burrell Shell and Tube Heat Exchanger. Serial Number: CR23779. Tube material: 316 stainless steel. Number of passes: 10. Number of tubes: 19. Tube dimensions: 1 inches diameter x 5 feet 6 inches Heat transfer surface area: 27.358 square feet approximate total tube volume: 33 gal. MAWP: 150 psi @ 400°F. MDMT: -20°F @ 150 psi. Inlets: [1] 1 inches diameter NPT [product], [1] 2 inches diameter FNPT [media]. Outlets: [1] 1 inches diameter NPT [product], [1] 2 inches diameter FNPT [media]. Overall dimensions: 6 feet 9 inches length x 2 feet 3-1/4 inches width x 3 feet 5-1/2 inches height.

Used G&H Shell and Tube Heat Exchanger - 26.5 square feet

Used G&H Shell and Tube Heat Exchanger. Model: T15190. Serial Number: CL30. Tube material: copper. Number of passes: 2. Number of tubes: 76. Tube dimensions: 1/2 inches diameter x 2 feet 8 inches L. Heat transfer surface area: 26.5 square feet Tube volume: 2 gal. For steam injected water heating. Inlets: [1] 4 inches diameter flanged port [shell, steam], [1] 2-1/2 inches diameter NPT [female, water]. Outlets: [1] 1 inches diameter NPT [shell, steam], [1] 2-1/2 inches diameter NPT [female, water]. Overall dimensions: 4 feet 1 inches length x 1 feet 5 inches width x 1 feet 3 inches height.

Used 1995 ITT Bell & Gossett “SU” Series Shell and Tube Heat Exchanger – 4.5 Square Feet

[2] Used 1995 ITT Bell & Gossett Shell and Tube Heat Exchangers. Model: SU-42-2. 2 pass design, ¾ inch O.D. copper tubes. Shell and tube side: MAWP: 150 PSI at 375ºF, MDMT: -20ºF at 150 PSI. Inlets/outlets: [2] 1-1/2 inch S-line. [3] 1 inch FNPT. Approximate weight: 56 lbs. Overall dimensions: 2 feet 7-3/4 inches L x 7-1/2 inches W x 8-3/4 inches H.[ACN14].

Used1998 ITT Bell & Gossett Stainless Steel SU-Series Shell and Tube Heat Exchanger - 86 Square Feet

Used 1998 ITT Bell & Gossett Stainless Steel SU-Series Shell and Tube Heat Exchanger. Model no. SU106-2. Total surface area of heat transfer: 86 square feet. Designated as a “2” pass unit. Materials of construction: 316 stainless steel head, 304 stainless steel tubes, tube sheet and shell. Shell side: MAWP: 150 psi at 375 ˚F, MDMT: -20 ˚F at 150 psi. Tube side: MAWP: 150 psi at 375 ˚F, MDMT: -20 ˚F at 150 psi. [3] Psi gauges. Unit has an Apex 5000 modular positioning system indicator, Mecair actuator and a Durco valve. ITT Steam trap. Model no. FT125C. Inlets/Outlets: [2] 1-3/4 inch FNPT flange diameter with [4] 5/8 inch mounting hole diameter 2-5/8 inch adjacent, 3-7/8 inch opposite. [2] 3 inch S-line. [1] 2 inch S-line. [1] ¾ inch FNPT. [1] ½ inch MNPT. Overall dimensions: 9 feet 2 inches L x 2 feet 5-1/4 inches W x 6 feet 6-1/2 inches H.[ACN176].

Used Chester Jensen Stainless Shell and Tube Heat Exchanger - 94.2 square feet

Used Chester Jensen Stainless Steel Shell and Tube Heat Exchanger. Model/Size: SV-20. Serial Number: 5620-C. Capacity: 18,000 pounds per hour [40 °F-90 °F], 20,000 pounds per hour [85 °F-190 °F], 20,000 pounds per hour [190 °F-230 °F]. Tube material: 316 stainless steel. Number of passes: 4. Number of tubes: 24. Tube dimensions: 1-1/2 inches diameter x 10 feet L. Heat transfer surface area: approx. 94.2 square feet Tube volume: 20 gal. Steam heated and fully CIP-able. The Ste-Vac heater is specifically designed to heat milk and milk products without formation of milk stone or "burn-on" on the heating surfaces. Ste-vac heaters can be used in: powdered milk production as a pre-heater, pasteurizing cream as high-temperature-short-time pasteurizers, pre-heaters for fluid milk before entering vat pasteurizers, ice-cream mix processing, pre-heating milk for separators, and for pasteurizing milk in cheese production. Inlets: [1] 3-1/2 inches diameter FNPT fitting [media], [1] 1-1/2 inches diameter S-line infeed. Outlets: [1] 1-1/2 inches diameter FNPT fitting, [1] 1-1/2 inches diameter S-line drain port. Overall dimensions: 11 feet 3 inches length x 2 feet 6 inches width x 6 feet 8 inches height.

Used Blaw Knox Shell and Tube Heat Exchanger - 25.3 square feet

Used Blaw Knox Shell and Tube Heat Exchanger. Serial Number: 5230. Stainless steel construction. Heat transfer surface area: approx. 25.3 square feet Heat exchanger dimensions: 18-3/4 inches diameter x 10 feet L. Tube lengths: 129-1/2 inches L. Inlets: [1] 1 inches diameter S-line fitting [product], [1] 3 inches diameter ANSI flange [steam]. Outlets: [1] 1 inches diameter S-line fitting [product], [1] 1-1/2 inches diameter FNPT. Overall dimensions: 11 feet length x 19 inches width x 53 inches height.

Used 2000 Enerquip Twin Shell and Tube Heat Exchanger System - 20 square feet

Used 2000 Enerquip Twin Shell and Tube Heat Exchanger System. Model: NEUC. Serial Number’s: 3128 and 3129. Nat’l Bd: 3327 and 3326. Tube material: 304 stainless steel. Number of passes: 2. Number of tubes: 32. Tube dimensions: 1/2 inches diameter x 2 feet 7 inches L. Heat transfer surface area: approx. 10 square feet Shell diameter: 6-1/2 inches Shell and tube side MAWP: 150 psi @ 375 °F. Shell and tube side MDMT: 150 psi @ -20 °F. Meters/controls: [4] Worcester Actuators, Series 39, [6] Fischer Pneumatic Actuators, Model 1-1/4 inches, [2] El-O-Matic Actuators, Type: ESA-65-4/A. Inlets: [1] 3 inches diameter NPT [jacket], [1] 2 inches diameter NPT. Outlets: [1] 1-1/2 inches diameter NPT [jacket], [1] 2 inches diameter NPT. Overall dimensions: 6 feet 4 inches length x 3 feet inches width x 6 feet 5 inches height. [ACN40]

Used 1990 Standard Refrigeration Co. Shell and Tube Heat Exchanger - 41.37 square feet

Used 1990 Standard Refrigeration Co. Shell and Tube Heat Exchanger - 41.37 square feet Model: QSST-1500. Tube material: copper. Number of passes: 5. Number of tubes: 44. Tube dimensions: 5/8 inches diameter x 5 feet 9 inches L. Heat transfer surface area: approx. 41.37 square feet Tube volume: 4 gal. MAWP: 350 psi @ 150° F. MDMT: 20°F @ 350 psi. Overall dimensions: 6 feet length x 2 feet 6 inches width x 9 inches H.[ACN25a]. [BI].

Used 2004 Yula Corp Active Waste Heater/Shell & Tube Heat Exchanger - 20.6 square feet

Used 2004 Yula Corp Active Waste Heater/Shell & Tube Heat Exchanger. Model: WC-1C-36BS. Serial Number: 19247. P.O. No. NR-2007-30-P11-2008. Tube Material : 316 stainless steel. Single pass. Number of tubes: 35. Tube dimensions; 3/4 inches diameter x 3 feet L. Heat transfer surface area: approx. 20 square feet Capacity: 2 gallons. Shell side MAWP: 150 psi @ 400 °F. MDMT: -20 °F @ 150 psi. Tube side MAWP: 150 psi @ 400 °F. MDMT: -20 °F @ 150 psi. Inlets: [1] 4 inches diameter flanged port [product], [1] 3 inches diameter [media]. Outlets: [1] 4 inches diameter flanged port [product], [1] 1-1/2 inches diameter FNPT fittings [media]. Yula Corp. sanitary heat exchangers are designed to be fully drainable on the sanitary side when mounted in proper position. Overall dimensions: 4 feet 2 inches length x 1 feet width x 1 feet 11 inches height. [ACN139].

Used 2004 Yula Shell & Tube Heat Exchanger - 12 square feet

Used 2004 Yula Shell & Tube Heat Exchanger. Model: WCV-6AA-66AAS. Serial Number: 19230. P.O. No. NR-2007-30-P11-2008. Tube material: 316 stainless steel. Number of tubes: 17. Number of tube passes: 6. Tube dimensions: 1/2 inches diameter x 5 feet 8-1/2 inches L. Heat transfer surface area: approx. 12 square feet Capacity: 0.90 gallons. Shell size: 4 inches Shell side MAWP: 150 psi @ 300 °F. MDMT: -20°F @ 150 psi. Tube side MAWP: 150 psi @ 300°F. MDMT: -20°F @ 150 psi. Inlets: [1] 1-1/2 inches diameter flanged port [steam]. Outlets: [1] 1-1/2 inches diameter flanged port [product], [1] 1-1/2 inches diameter FNPT fittings [steam]. Originally installed with Eli Lilly for a water to water application. End cap with product inlet is missing. Overall dimensions: 5 feet 10 inches length x 9 inches width x 2 feet 4 inches H.[ACN74].

Used Dunham-Bush Shell and Tube Heat Exchanger - 94.2 square feet

Used Dunham-Bush Shell and Tube Heat Exchanger. Model: C00SF1514496302. Serial Number: 1081585. Nat'l Bd: 12356. Tube material: carbon steel. Number of passes: 1. Number of tubes: 64. Tube dimensions: 5/8 inches diameter x 9 feet L. Heat transfer surface area: approx. 94.2 square feet Tube volume: 9 gal. Shell side MAWP: 400 psi at 200°F. Tube side MAWP: 250 psi at 200 °F. Inlets: [1 ] 2 inches diameter media flange, [1] 2 inches diameter product flange. Outlets: [1] 2 inches diameter media flange, [1] 2-1/2 inches diameter product flange. Overall dimensions: 12 feet 6 inches length x 8 inches width x 3 feet 5 inches height.

Used Chester Jensen Ste-Vac Heater - 92.25 square feet

Used Chester Jensen Ste-Vac Heater. Model: SV-20. Capacity: 18,000 pounds per hour [40 °F-90 °F], 20,000 pounds per hour [85 °F-190 °F], 20,000 pounds per hour [190 °F-230 °F]. Number of tubes: 24. Length of inner tubes: 10 feet Tube diameter: 1-1/2 inches "The economical, no burn-on flavor saver". Steam heated and fully CIP'able. The Ste-Vac heater is specifically designed to heat milk and milk products without formation of milk stone or "burn-on" on the heating surfaces. Ste-vac heaters can be used in: powdered milk production as a pre-heater, pasteurizing cream as high-temperature-short-time pasteurizers, pre-heaters for fluid milk before entering vat pasteurizers, ice-cream mix processing, pre-heating milk for separators, and for pasteurizing milk in cheese production. Inlets: [1] 1 inches diameter NPT [female, media], [1] 1-1/2 inches diameter S-line fitting [product]. Outlets: [1] 1 inches diameter NPT [male, media], [1] 1-1/2 inches diameter I-line fitting [product]. Overall dimensions: 10 feet 8 inches length x 33-1/2 inches width x 74 inches height. [XMR5]

Used Ste-Vac Shell and Tube Heat Exchanger

Used Ste-Vac shell and tube heat exchanger, 1 inches tubes 6 feet long.

Used Shell and Tube Heat Exchanger - 7.85 square feet

Used Shell and tube heat exchanger, 316 stainless steel on tube side. 8 square feet, [3] 1 inches x 10 feet long tubes, vertical, 1 pass, 0A dim = 3-1/2 inches diameter by 11 feet long.

Used Standard Refrigeration Co. Shell and Tube Heat Exchanger - 10.47 square feet

Used [2] Standard Refrigeration Co. Shell and Tube Heat Exchanger. Model: OLDX-5-A2. Tube material: copper. Number of passes: 4. Number of tubes: 20. Tube dimensions: 1/2 inches diameter x 4 feet L. Heat transfer surface area: approx. 10.47 feet square Tube volume: 0.8 gallons. Tube side MAWP: 225 psi. Shell side MAWP: 350 psi. Inlets: [2] 1 inches diameter ports, [1] 1-1/2 inches port [media]. Outlets: [2] 1 inches diameter ports, [1] 1-1/2 inches diameter port [media]. Overall dimensions: 4 feet 6 inches length x 10 inches width x 1 feet 2 inches height. [ACN16].

Used California Hydronics Skid Mounted Hot Water Set - 19.6 square feet

Used California Hydronics Skid Mounted Hot Water Set. Bell & Gossett Shell and Tube Heat Exchanger, Model: SU-65-2, Ref. No’s: 93Y77202-03-3 and 5-260-06-060-001, Nat’l Bd: 30030, tube material: copper, number of passes: 2, tube dimensions: 5/8 inches diameter x 5 feet L, heat transfer surface area: approx. 19.6 square feet, tube volume: 2 gal. Bell & Gossett Shell and Tube Heat Exchanger, Model: SU-85-4, Ref. No’s: 93Y77202-01-3 and 5-261-08-060-033, Nat’l Bd: 30027, tube material: copper, number of passes: 4, number of tubes: 44, tube dimensions: 5/8 inches diameter x 5 feet L, heat transfer surface area: approx. 41 square feet, tube volume: 3.5 gal. [2] Condensate Tanks- 10 Gallon, MAWP: 125 psi at 210 °F. Unit is equipped with [2] electro-pneumatic valves and [2] Jordan pressure relief valves. [2] Bell & Gossett Centrifugal Pumps, Model: 11/28C, MAWP: 175 psi, capacity: 60 gallons per minute at 50 ft, 1800 rpm maximum. [2] Baldor Industrial Motors, 3 horse power, 1,725 rpm, 230/460 V, 8.2/4.1 amps, 60 Hz, 3 phase. Inlets: [1] 2 inches threaded fitting[female], [1] 4 inches diameter pipe [steam]. Outlets: [1] 2 inches diameter pipe [steam], [1] 2 inches diameter pipe [product]. Overall dimensions: 8 feet 4 inches length x 4 feet 4 inches width x 7 feet 1 inches height.

Used California Hydronics Skid Mounted Hot Water Set

Used California Hydronics Skid Mounted Hot Water Set. Heat exchanger dimensions: 10 inches diameter x 61 inches L. [2] Condensate Tanks- 10 Gallon, MAWP: 125 psi at 210 °F. Unit is equipped with [2] electro-pneumatic valves and [2] Jordan pressure relief valves. [2] Bell & Gossett Centrifugal Pumps, Model: 11/28C, MAWP: 175 psi, capacity: 60 gallons per minute at 50 ft, 1800 rpm maximum. [2] Baldor Industrial Motors, 3 horse power, 1,725 rpm, 230/460 V, 8.2/4.1 amps, 60 Hz, 3 phase. Inlets: [1] 2 inches threaded fitting[female], [1] 4 inches diameter pipe [steam]. Outlets: [1] 2 inches diameter pipe [steam], [1] 2 inches diameter pipe [product]. Overall dimensions: 100 inches length x 52 inches width x 85 inches height.

Used Stainless Steel Essence Recovery System - 65.9 sq. ft.

Used Stainless Steel Essence Recovery System. Re-boil u-tube capacity: 328 lbs/hr. [1st] Whitlock Hi-Transfer shell and tube heat exchanger/condenser: [222] 5/16 in. dia. x 36 in. L tubes and 65.9 sq. ft. of surface area. [2nd] Whitlock Hi-Transfer shell and tube heat exchanger: [84] 5/16 in. dia. x 36 in. L tubes and 24.7 sq. ft. of surface area. Essence cooler: [12] 1-3/8 in. dia. x 15 ft. L tubes. Essence column dimensions: 11-1/2 in. inner dia x 17 ft. H. System is used to "strip" feed juices of their flavor by evaporation and to "concentrate" these esters in a distillation column. Overall dimensions: 10 ft. L x 5 ft. W x 24 ft. H.[hb1].

Used Bell and Gossett SU-Series Shell and Tube Heat Exchanger - 71 square feet

Used Bell and Gossett SU-Series Shell & Tube Heat Exchanger. Model: SU105-2. Carbon steel shell. [76] ¾ inches diameter x 5 feet length copper multi-tubes. Heat transfer surface area: ~ 71 square feet Tube volume: 8.7 gal. The SU-series tube bundles are of “U”-bend construction. This allows ample expansion or contraction for wide temperature variations. Tube spacers properly support and space each tube for maximum efficiency in steam condensing and drainage. Inlets: [1] 6 inches diameter flanged port [media], [1] 4 inches diameter FNPT [product]. Outlets: [1] 4 inches diameter FNPT [product], [1] 1 ½ inches diameter port [media]. Overall dimensions: 5 feet 4 inches length x 1 feet 2 inches width x 1 feet 6 inches height. [ACN50a]

Used Shell and Tube Heat Exchanger

Used Shell and Tube Heat Exchanger Assembly.

Used Heat Set

Used Heat Set 3-1/2 in.

Used Stainless Steel Heat Set

Used Stainless Steel Heat Set. Pneumatic positioner: Model no. PPR-55-3000-4R42021. Tru-Flo actuator. Type: UT31-SR4-F07. 150 max PSI. Inlets/outlets: [2] 3 inch S-line. [1] 2 inch S-line. [1] 1 inch FNPT. 4 feet ½ inch inside shaft with 3/8 inch dia. holes. Overall dimensions: 7 feet 9-1/2 inches L x 1 foot 7 inches W x 10 inches H.

Used Shell and Tube Heat Exchanger

Used Shell and Tube Heat Exchanger. 2 ft. 6 in.

Used 1990 Bell & Gossett SU-Series Shell and Tube Heat Exchanger – 75 Sq. Ft.

Used 1990 Bell & Gossett SU - Series Shell and Tube Heat Exchanger. Heat transfer surface area: 75 sq. ft. Materials of construction: cast iron head, steel shell and ¾ in. copper tubes. Design pressure: 150 PSI. Test pressure: 300 PSI. Design temperature: 375°F. Diameter: 8 ft. 5 /8 in. The SU-series tube bundles are of “U”-bend construction. This allows ample expansion or contraction for wide temperature variations. Tube spacers properly support and space each tube for maximum efficiency in steam condensing and drainage. Inlets/Outlets: [1] 6 in. effective port flange dia. [8] 7/8 in. mounting hole dia. [2] 2-1/4 in. FNPT. [1] 5/8 in. FNPT. Approximate shipping weight: 364 lbs. Overall dimensions: 9 ft. 7 in. L. x 1 ft. 4 in. W. x 1 ft. 1 in. H.

Used SU-Series Shell & Tube Heat Exchanger – 18 Sq. Ft.

Used [2] SU-Series Shell & Tube Heat Exchangers. 2-Pass design with 316 stainless steel heads. Approximate area heat exchange surface area: 18 square feet. [22] tubes of inner dimensions: 4 feet 11 inches L x 5/8 inch diameter. Outer diameter of tube: ¾ inch. Inlets/outlets: [1] 4-1/2 inch flange with [8] ¾ inch mounting holes. 2-7/8 inch adjacent, 7-1/2 inch opposite. [1] 3 inch flange with [4] ¾ inch mounting holes. 4-1/4 inch adjacent, 6 inch opposite. [1] 3 inch S-line. [1] 1-1/2 inch FNPT. The SU-series tube bundles are of “U”-bend construction. This allows ample expansion or contraction for wide temperature variations. Tube spacers properly support and space each tube for maximum efficiency in steam condensing and drainage. Overall dimensions: 6 feet 3 inches L x 1 foot 4 inches W x 1 foot ½ inch H.